Pocket Monster Toothbrush Case – Meowth Edition

Meowth Edition is here — a print-in-place toothbrush case that combines a clean, collectible look with a practical everyday function you'll actually use.

Ready in about 1 hour using only ~15g of material, it keeps AMS waste low by limiting the colored details to the first layers.

Available in two sizes for kids and adults, it helps keep your toothbrush protected, ventilated, and clean — perfect for travel, school, gym bags, daily carry, or simply adding a little Pocket Monster charm to your bathroom routine.

Boost Me 💚 Enjoying the model? Give it a BOOST! BOOSTS cost nothing and help independent designers reach more people.

If you like this model and want to support my work, a BOOST makes a huge difference. Thank you! More Pocket Monster Editions

Looking for other characters?

- Pikachu / 💧 Squirtle / 🌿 Bulbasaur / 🔥 Charmander -  Full Starter Pack - Eevee - Eevee Edition - Squirtle Squad - Squirtle Squad - Snorlax - Snorlax Edition - Mew - Mew Edition - Umbreon - Umbreon Edition - Charizard - Charizard Edition - Psyduck - Psyduck  Edition - Gengar - Gengar Edition

Printing Instructions

This is a compact, precision print-in-place mechanism — proper extrusion is key for best results.

PLA or PETG is recommended. Other materials may work, but performance can vary.

No supports required.

Default settings work well.

Choosing the Right Profile (Recommended)

Start with the Standard profile .

If needed:

- Too tight (hard to open / stuck) → use Loose Fit profile - Too loose (weak latch / low resistance) → use Tight Fit profile These profiles already adjust extrusion to compensate for filament variation.

Fine Tuning (Optional)

This is a small precision part — extrusion accuracy directly affects the latch behavior.

If you prefer manual tuning:

- Too tight → slightly reduce Flow Ratio - Too loose → slightly increase Flow Ratio Adjust in small steps (±0.05) and reprint if needed.

Each filament behaves differently — even the same spool over time.

A visual guide is included in the image gallery.

👉 This model can also be used as a quick real-world flow calibration test.

First Use

The latch may feel firm on the first open.

Open and close it a few times — it will settle into a smooth and consistent motion.

Personal Use Only This model is intended for personal, non-commercial use only.

Description

This Meowth Edition brings a playful, mischievous, and instantly recognizable personality to the Pocket Monster Toothbrush Case collection — combining practical everyday protection with a clean collectible design inspired by one of the most iconic and beloved creatures in the franchise.

Fully print-in-place , it requires no assembly and is ready to use straight off the printer. The integrated latch keeps the case securely closed, while the ventilation openings help the toothbrush dry properly after use — making it ideal for travel, school, backpacks, bathroom organization, gym bags, or everyday carry.

Ready in about 1 hour and using only around 15g of material, this is a fast and efficient print with surprisingly low AMS waste, since all visible colored details are concentrated mostly in the first layers.

Designed in two sizes for kids and adults, the case works with a wide variety of toothbrushes while maintaining a compact and portable form factor. It protects the toothbrush during transport while adding personality, character, and a collectible touch to an everyday object that normally receives very little attention.

The geometry was carefully refined to balance print reliability, smooth operation, durability, and satisfying mechanical feedback. The latch mechanism is compact but precise, creating a clean print-in-place action with no supports required and virtually no post-processing.

This model was also optimized specifically for efficient multicolor printing. Unlike many decorative AMS projects that generate excessive purge waste, the visible character details remain concentrated primarily in the first layers, dramatically reducing filament consumption while preserving the recognizable appearance of the character.

Beyond functionality, Meowth brings a lighter and more playful personality to the collection. The rounded face, simple expression, signature forehead coin, and clean color palette create a design that feels both nostalgic and timeless. It works especially well with matte filaments and textured build plates, giving the finished print a soft toy-like appearance while remaining fully functional.

The character's simple facial features also translate exceptionally well to 3D printing, creating a clean and highly recognizable result without requiring excessive color changes or complicated printing setups.

This 3D printable toothbrush case functions as a portable toothbrush holder, travel toothbrush cap, hygienic bathroom accessory, or compact storage solution for everyday use. The ventilated structure helps reduce trapped moisture while keeping the toothbrush protected, organized, and ready to carry anywhere.

Perfect for makers who enjoy functional prints, compact EDC accessories, print-in-place mechanisms, multicolor printing, collectible designs, kawaii-inspired objects, and practical everyday items with personality. Suitable for kids, adults, travelers, Pokémon fans, collectors, and anyone looking for a useful but expressive 3D printed accessory.

A great addition to any collection of functional prints — combining portability, fast printing, low material usage, satisfying mechanics, nostalgic character appeal, and real-world practicality in a compact design that's both decorative and genuinely useful.