
Quick-release shelf fastenings in the Haval H3 trunk (Cool Dog)
Model details
- Platform
Thingiverse
- Price
- Free
- License
- CC-BY-NC-SA
- Non-commercial use only, with credit; share remixes under the same license.
- 16 Likes
- 173 Downloads
- 0 Makes
- 1 Collected
- 3 Comments
- 959 Views
Description
Mounts shelf-curtain fasteners with the possibility of quick removal, two types - vertical installation v1 and installation with reclined seat backs v2 (it is also removed only after reclining the backs). For curtains tube with dimensions of 185x49x44 mm. This is not a stock shelf, but one of the universal options, so if there are differences in size, change it for yourself (I also posted the source code, it's drawn in COMPASS-3D v22 - everything is quite simple there).
Glue the fasteners themselves to double-sided adhesive tape, no more than 1 mm thick - this is quite enough, with the curtain installed, these fasteners are securely held by the geometry of the sidewalls, the tape is actually needed only to hold the fasteners when the shelf is removed (but there is also a hole for fastening with a self-tapping screw).
It is enough to print with 2-3 perimeters and 30% filling, there will be no high loads here in principle - and even these parameters are beyond the scope.
--------------------------------------------
Быстросъемные крепления полки\шторки в багажник Haval H3 (CoolDog)
Крепления полки-шторки багажника с возможностью быстрого снятия, два вида - вертикальной установки v1 и установки с откинутыми спинками сидений v2 (соответственно снимается тоже только после откидывания спинок). Сделаны из расчетов тубуса шторки с размерами 185x49x44 мм - это не штатная полка, а один из универсальных вариантов, поэтому при отличиях в размерах - измените под себя (исходники тоже выложил, нарисовано в КОМПАС-3D v22 - там всё довольно просто).
Сами крепления приклеить на двусторонний скотч, толщиной не более 1 мм - этого вполне достаточно, с установленной шторкой эти крепления надежно держатся геометрией боковинок, скотч по факту нужен только для удержания креплений когда полка снята (но отверстие под крепление саморезом тоже есть).
Печатать достаточно с 2-3 периметрами и 30% заполнением, высоких нагрузок тут впринципе не будет - и даже этих параметров заглаза.
Similar models


Console cup containers for Haval H3 (CoolDog) 2024

Plug push-button for Transmission Mode Selector Haval H3 (CoolDog) 2WD

Plug/Container for Transmission Mode Selector Haval H3 (CoolDog) 2WD

Modification of the console cup holders for Haval H3 (CoolDog) 2024

Center console cup holders Haval H3 (CoolDog) 2024

Foldable hooks mounts

Riverboat project 376 "Yaroslavets", HO scale

Impact printhead Remix for Creality Ender 3 / NEO / PRO (not E3 V2 V3) Printhead HGX-Lite with mount for CR-touch
ENDER 3 EXTRUDER COVER COOLING AND MOUNT FOR BL TOUCH (3D TOUCH)
Gizmo’s Barbie Car 3D Printing Model | Assembly + Action

Elegoo Neptune 3 Pro Klipper Upgrade with BTT Pi v1.2
Names are used only to indicate the source of a result. Polyzon is not affiliated with the listed sites.











