A1 side drag chain, cable chain

0.2mm layer, 3 walls, 20% infill V1.1 - Updated base mount to accommodate wider range of ferrite core position.

The print profile shared would be slightly slower but it's set to be the most stable and lowest risk of failed print. For best print outcome, PLEASE clean your build plate with alcohol wipe for best bed adhesion/print outcome.

0.2mm layer, 3 walls, 20% infill with cable clip Cable clip on chain clip for ones that have BIQU led

A1 - 0.2mm Layer, 3 Wall, 20% Cubic, Outer 1st, 250mm/s Original Build Plate with settings tweaked for best surface quality without increasing the original print time.

- Inner / Outer / Inner wall order and avoid crossing wall for best surface finish - Reduced filament slowdown with extra fan cooling for consistent print speed and flow - Cubic Infill to offset extra wall avoidance time without compromising infill strength - 250mm/s wall speed to match original print time

3 in 1: improved profile, pivot -30°, no-wobble-bottom Usé como base el perfil de @MikeR para aprovechar sus mejoras en la calidad de la superficie, añadí las piezas modificadas por @PixelFanLabs para permitir que el soporte de la base pivote completamente hacia abajo y así evitar que las partes superior e inferior se toquen o presionen entre sí, y modifiqué la pieza Body1 (el pie) siguiendo el modelo de @technokul para ajustar la base a la altura correcta. Finalmente, reorganicé un poco las nuevas piezas para distribuirlas de manera homogénea en la placa.

A1 mini Profile 0.2mm layer, 3 walls, 20% infill A1 mini Profile

- 0.2mm layer - 3 walls - 20% infill

More flexible and horizontal oriented print I realized this print profile merging different print profiles and settings.

Specifically, I horizontal oriented all the pieces and used the @PixelFanLabs fixed pivot to be sure to don't ruin the cable.

I used the 0.2 Standard preset with the following changes:

- 3 wall loops - 20% infill - Gyroid infill pattern - On build plate only support

Clip on Top Mount, -30° Pivot, No Wobble Bottom This is basically @Rintxy's print profile with the top mount replaced with a clip on style mount. I was having trouble closing the cover properly with the original top mount installed, so replaced it with this.

Fixed Pivot to -30deg (0.2mm Layer, 3 walls, 20% infill) Updated the model to allow the base mount to pivot all the way down. This was to fix the issue where the top and bottom part would touch and push against each other in the lower Z-axis ranges. It was also putting more strain on the Z-axis. I have added before and after photos.

Updates:

- Update to the Pivot piece to allow it to sit flat agaisnt the base piece at the bottom angle - Update to the Base piece to allow the Pivot to go to -30 degrees - Update to the Base Cover piece to allow more space for the cable to pass so it can drop freely Print Profile Details:

- Added Variable layer height to make the top areas more rounded and less stepped (Better but not perfect) - 0.2mm Layer - 3 walls - 20% infill

Double clips for PandaLux & Webcam power. for the webcam clips I had to heat one of the clips with a torch and make them smaller to hold a smaller cable.

No Wobble ,0.2mm layer, 3 walls, 20% infill No‑wobble remix of the original Bambu Lab Studio drag-chain mount. Foot geometry is updated for a lower 2.5 mm front lip to sit flat and eliminate wobble while keeping all other dimensions, cable path, and features identical to the stock design.

0.2mm layer, 2 walls, 15% infill I have remixed the ' A1 top mount test fit V26.2 P1 ' to address an issue I encountered on my printer. The original design has a base that is too thick, which elevated my printer off its surface and introduced instability. This modified version features a thinner base, with 2.45 mm of material removed , to ensure a flush and stable fit.