Harry Potter Wands

Elder 0.16mm layer, 2 walls, 15% infill

Hermione 0.2mm layer, 2 walls, 15% infill

Harry Potter 0.16mm layer, 2 walls, 15% infill

Snape 0.16mm layer, 2 walls, 15% infill

Sirius 0.2mm layer, 2 walls, 15% infill

McGonagall 0.2mm layer, 2 walls, 15% infill

Voldemort 0.2mm layer, 2 walls, 15% infill

Fleur 0.2mm layer, 2 walls, 15% infill

Ginny 0.2mm layer, 2 walls, 15% infill

Draco 0.2mm layer, 2 walls, 15% infill

Ron 0.2mm layer, 2 walls, 15% infill

Luna 0.2mm layer, 2 walls, 15% infill

Narcissa 0.2mm layer, 2 walls, 15% infill

Lucius 0.2mm layer, 2 walls, 15% infill

Nymphadora 0.2mm layer, 2 walls, 15% infill

Harry Potter A1 Mini 0.16mm layer, 2 walls, 15% infill Print profile adjusted to work on the A1 Mini, no adjustments have been made to the size

A1 mini Hermione - 0.16mm layer, 2 walls, 15% infill

[Coloured] Elder 0.2mm layer, 4 walls, 15% infill - 0.2 layer height - 4 walls - Dark brown and beige colour. - Improved settings to fit the A1 limitations. - Easy to remove supports. - 3 models, fully painted, filament saving painted, and one colour.

Voldemort wand - 0.16mm layer, 2 walls, 15% infill

ELDER WAND - 0.16mm layer, 3 walls, 15% infill The wand's orientation in the original print file caused me a lot of quality issues in some areas, especially at the tip. I adjusted the tilt to be more horizontal.

Harry - 0.6mm nozzle, 0.3mm layer, 3 walls, 15% infill Printed with Wood PLA and a 0.6mm nozzle after the wood particles clogging my 0.4mm nozzle.

0.3mm layer, 3 walls, 15% infill, slowed speed on initial layer for better adhesion, A1 min

0.16mm layer, 4 walls, 15% infill Angled for better support and less scaring.

voldemort 0.16mm layer, 6 walls - 30 degrees save support lower angle so that you use less supports, original uses almost as much on supports as wand

42cm Bambu A1! 0.08mm layer, 2 walls, 100% infill Printed from bottom corner to top corner to have realistic size (42cm total length on 25x25x25 print plate), also made it fully solid for strength. Set to 0.08 mm for best details, takes a while to print tho ~14h, using brown esun pla.

After that I did some spraypainting (mat-black) in the wind so that it feathered out over the wand and later taped and fully sprayed the golden handle, I personally think it came out amazing.

0.16mm layer, 2 walls, 15% infill- 7 on one plate !! So it is possible to get 7 on one plate - only 7h print and You have all in one - ready to print just from the app :)

Have fun !!

McGonagall

Hermione

Snape Voldemort / Tom Riddle Nymphadora

Harry Potter

Luna

Voldemort - 2 piece for A1 mini 0.16mm layer, 2 walls 0.16 mm layer, 2 walls, 15% infill

Added manual support for the base

Single triangle connector

the wand is slightly resized in order to fit larger connector

If needed slightly cut down the connector to achieve perfect fit

Snape - A1 mini 2 piece 3 joints 0.16mm layer, 2 walls This model in original has a empty space between the wand and the base and when printed they connect with supports and don't hold together so this model fills the empty space when printed upright

0.16 or 0.2 with casual supports and brim