Fidget Ghost

The "Keeps Your Hands Busy" Fidget Ghost 👻

A fidget toy for your desk. It sits flat as a friendly ghost, and every way you move the stem gives it a different look.

🟩 𝗪𝗔𝗬𝗦 𝗧𝗢 𝗣𝗟𝗔𝗬

▸ 𝗧𝘄𝗶𝘀𝘁 𝘁𝗵𝗲 𝗦𝘁𝗲𝗺 — Leave it flat on the desk and twist. The rings shift against each other into new designs.

▸ 𝗣𝘂𝘀𝗵 𝗮𝗻𝗱 𝗣𝘂𝗹𝗹 — Slide the stem from side to side and the rings move around to their stops for a whole different set of visuals.

▸ 𝗟𝗶𝗳𝘁 𝗜𝘁 𝗨𝗽 — Raise it by the stem with a slight twist and the 22 rings drop into a cone-like shape.

▸ 𝗛𝗲𝗮𝗿 𝗜𝘁 𝗦𝗲𝘁𝘁𝗹𝗲 — Raise and lower it on the desk and it makes a satisfying sound as the rings come back down.

▸ 𝗧𝗲𝘅𝘁𝘂𝗿𝗲𝗱 𝗦𝘁𝗲𝗺 — The stem is textured, so it has a tactile feel under your fingers while you fidget.

🟩 𝗪𝗛𝗔𝗧 𝗠𝗔𝗞𝗘𝗦 𝗜𝗧 𝗪𝗢𝗥𝗞

▸ 𝗣𝗿𝗶𝗻𝘁𝘀 𝗶𝗻 𝗣𝗹𝗮𝗰𝗲 — One print, no assembly. All 22 rings and the stem come off the plate already captured inside each other.

▸ 𝗕𝘂𝗶𝗹𝘁 𝘁𝗼 𝗛𝗼𝗹𝗱 𝗧𝗼𝗴𝗲𝘁𝗵𝗲𝗿 — An even gap of about 1mm between every ring keeps the ghost shape intact, so the rings slide and drop without coming apart.

▸ 𝗧𝗵𝗲 𝗘𝘆𝗲𝘀 𝗔𝗿𝗲 𝗣𝗿𝗶𝗻𝘁𝗲𝗱 𝗜𝗻 — Two black eyes, one layer deep, for only two filament changes and under 3g of purge.

🟩 𝗖𝗛𝗘𝗖𝗞 𝗬𝗢𝗨𝗥 𝗕𝗘𝗗 𝗙𝗜𝗥𝗦𝗧

▸ 148 x 179mm and 39mm tall with the stem. Leave room beside it for the prime tower if you print the eyes in black.

🟩 𝗣𝗥𝗜𝗡𝗧 𝗦𝗘𝗧𝗧𝗜𝗡𝗚𝗦

No supports required · no brim · 0.20mm layer height · 2 walls · 10% grid infill · PLA

Printed on a Creality Hi 1 in 3h 55m and 105g. Happy fidgeting! 👻