Loisirs et makers

3D Models of Axial Gearboxes and Reduction Drives

This collection gathers 3D models built around axial and reduction gearboxes: planetary stages, RC crawler transmissions, bevel gear pairs and small gear-driven toys. Most of them are meant for 3D printing on a home FDM machine, though the required tolerances vary a lot between a desk toy and a loaded drivetrain. The list is useful when you need a gear reduction for a project and want to compare several layouts before committing to one. Polyzon does not confirm whether models are free, their price, license, official status, affiliation, safety or fitness. Check the current terms at the source.

Le texte de cette collection est rédigé en anglais ; la recherche, elle, fonctionne dans toutes les langues.

Une collection Polyzon · 47 modèles sur 3 plateformes

Comment cette collection est composée

Polyzon compose cette collection à partir des résultats de recherche des plateformes connectées. Les doublons et les modèles sans aperçu sont retirés, les correspondances faibles sont placées à la fin, et le reste suit l’ordre de la recherche. Les modèles appartiennent à leurs auteurs : consultez les conditions sur la page de chaque modèle.

Règles de sélection : la rédaction de Polyzon · Texte mis à jour le 15/10/2026

Voir la collection Tout afficher : 2304 modèles →
Collection

Par où commencer

Tous les modèles de cette collection

Tout afficher : 2304 modèles
À propos de la catégorie

«3D Models of Axial Gearboxes and Reduction Drives»

Planetary designs appear in both single-stage and stacked versions, where several stages are chained to reach a higher reduction. RC-oriented entries tend to be complete transmission housings with mounts and skid plates that fit a specific chassis family, while standalone gear sets are just the toothed parts. Bevel and right-angle units change the direction of the drive, which matters when the motor has to sit along the chassis rather than across it.

Before printing, look at the reduction ratio and what it implies for torque and speed, then check the module or tooth profile the author specifies, since mixing profiles from two sources rarely works. Read the part list: how many pieces the assembly has, whether bearings, shafts or screws are required, and whether the author printed it in one piece or in sections. Layer height, wall count and material choice affect how well teeth mesh, so the settings on the model page are worth following closely, and photos of finished prints show how the parts actually fit together.

If the results feel narrow, try related wording: transmission, transfer case, speed reducer, worm drive, cycloidal drive, or the ratio you need, such as 1:10 or 1:36. Searching by the chassis or scale you are building, or by the shaft diameter and bearing size, often narrows the list faster than the word gearbox alone. Combining a gearbox term with mount, housing or adapter brings up the surrounding parts rather than the gears themselves.

FAQ

Questions fréquentes

What reduction ratios do these gearbox models usually cover?
Ratios range from a few units to one up to roughly several dozen to one, and multi-stage planetary designs reach the higher end by stacking stages. The ratio is normally stated in the title or the model description, so compare it with the speed and torque your project needs.
Do these gearboxes need supports when printed?
It depends on the orientation the author chose. Flat housings and gear plates often print without them, while overhanging mounts and shafts may need them; the model page usually states the recommended orientation and whether supports are used.
Which parts are not printed?
Bearings, shafts, screws and sometimes gears are commonly bought rather than printed. Check the description for the hardware list and the dimensions it expects before starting.
Can I scale a gearbox model up or down?
Scaling changes tooth size and clearances, so a scaled gear set may jam or run loose. If you need another size, look for a model designed for that scale or shaft diameter instead of resizing an existing one.
Voir aussi
Objets

3D Models of Gear Reducers and Gearboxes to Print

133033 modèles
Outils et équipement

3D Models of 3:1 Gear Reducers and STL Files

11764 modèles
Loisirs et makers

Differential Gear 3D Models and STL Files

28751 modèles
Outils et équipement

Trimmer Reducer 3D Models and STL Parts

2579 modèles
Outils et équipement

Planetary Gearbox STL Models for 3D Printing

46399 modèles
Électronique

Wind Generator with Gearbox: 3D Models and STL

15660 modèles

Toutes les catégories de modèles 3D

Le catalogue complet des thèmes, de la maison à la CNC, avec une recherche sur tous les sites connectés.

Ouvrir le catalogue des catégories